Views: 2 | Downloads: 0
Coal seam gas (CSG) emission in coal mines can create unsafe working conditions, where occurrences of coal and gas outbursts are responsible for many mining accidents resulting in injury and death. High CSG emissions also cause economic losses due to production stoppages and increases the costs associated with mine ventilation. Mining at the Velenje Coal Mine is made difficult, not just because of the depth of the seam (500 m), but because of the high CSG emissions. The lignite coal seam is also heterogeneous which comprises of different porosities and fracture systems that act as gas reservoirs in which CSG can be trapped under high pressure, creating an ever-present risk of coal and gas outbursts.
Coal seam gas drainage methods are one of the main tools for minimizing CSG emissions in mines and many different drainage techniques have been developed in coal mines around the world. At present, methods for draining CSG can be divided into pre-drainage and post-drainage with in-seam goaf drainage. Here at the Velenje Coal Mine the CSG composition is predominately CO2 and CH4 and because of the high gas emission (up to maximum 10 m2/t of extracted coal), the the mine implemented the first pre-drainage test in 2013, to minimize the CSG emission at the longwall face.
The research work reported herein focuses on the numerical modelling of CSG gas flow around a drainage borehole with the aim of simulating gas drainage from a borehole and CSG migration in the lignite seam. The absence of gas drainage models in the literature describing thick lignite seams highlights the need for a study such as this in order to better understand the mechanism of CSG migration before and during CSG drainage. In the first stage of this research the emphasis was on understanding the geomechanical characteristics of the lignite and geochemical characteristics of the CSG. This included CSG composition monitoring, making CSG borehole pressure measurements, and performing CSG carbon isotope analysis. The highest CSG pressures (up to 2.5 MPa) were found in the first mining level under fresh overburden. The stable carbon isotope composition of CH4 and CO2 indicate that methane was generated via acetate fermentation and the reduction of CO2 (13CCH4 from -70.4 to -50.0 ‰), which was confirmed by the α13CCO2-CH4 fractionation factor. The higher values of δ13CCH4 also indicate that thermogenic methane (13CCH4 values from -50.0 to -18.8 ‰) migrated from deeper layers in the basin. δ2HCH4 at the longwall faces varied from -358.5 to -291.4 ‰. The different Velenje lignite lithotype groups, which consist of xylite and detrite, are also discussed in detail since their geomechanical characteristics greatly influence gas adsorption capacity, geomechanical strength and gas flow characteristics of the seam.
Active seismic tomography was also conducted across two 100 m sections of two longwall panels: K.-130/B and K.-50/C. At the longwall panel K.-130/B the P-wave velocities decreased by up to 600 m/s as the face moved closer to the tomography zone at longwall panel K.-130/B and by up to 250 m/s in the case of longwall panel K.-50/C. An increase in the S-wave velocity to 400 m/s was measured as the K.-130/B longwall face advanced. The data obtained from active tomography monitoring is used for numerical modelling set-up.
State-of-the-art computer numerical modelling software is used to construct a gas flow model to simulate gas migration and drainage in the coal seam during excavation. Geomechanical modelling was performed using FLAC3D software for different lithotypes: 100% xylite, 100% fine detrite and a 50% of xylite and 50% of fine detrite mixed lithotype. Maximum vertical stresses vary depending on lithotype and were the highest for the detrite lithotype (23 MPa) during horizontal excavation. The distance to the longwall face, where these maximum values occur, varied from 6.7 m for detrite to 7.9 m for xylite and 6.8 m for mixed lithotype coal. The Top Coal Caving models produced maximum vertical stresses at 22 m in front of the longwall panel. The maximum vertical stresses were 24 MPa in detrite, 26 MPa in xylite and 30 MPa in mixed lithotype respectively. The CSG flow modelling was also performed using TREACT version of TOUGH2 software with ECO2N equation-of-state (EOS). The most efficient gas drainage occurs, when the borehole is between 40 m and 20 m to the longwall in all lithotype groups. When the borehole < 20 m to the longwall face, the pressure drops to almost the atmospheric pressure, but gas still flows. Closer to the longwall face (5 m) gas flow is reduced to the level that drainage is no longer possible.
Combining the data from these geomechanical and gas flow models revealed the complex relationship between stress, permeability and gas migration through the lignite. These results will be vital in the future design of an efficient drainage system for the Velenje Coal Mine and for thick or steep coal seams in general.